基于CFD/CSD耦合的叶轮机叶片失速颤振计算

为了研究叶轮机叶片的失速颤振特性,发展了一种计算流体力学与计算结构力学(CFD/CSD)时域耦合方法。该方法通过每一物理时刻CFD和CSD的循环迭代实现了耦合计算。在CFD分析中,采用鲁棒性较好的空间离散格式AUSM+-UP,并基于延迟脱体涡模型(DDES)模拟了带分离流动。在结构分析中,通过模态法构建了旋转叶片动力学方程并运用杂交多步方法进行求解。以孤立转子Rotor37为例,计算了不同工况下流场总体与细节参数,与实验结果的对比验证了CFD算法的精度。对某转子叶片进行了颤振特性研究,计算所得的广义位移时间响应曲线表明该叶片在近失速工况下会发生失速颤振,其表现形式为一阶弯曲模态发散且各阶模态之间不耦合。分析表明,流场不稳定和非定常效应是引起失速颤振的关键因素,同时折合频率的降低也会导致原本气动弹性稳定的叶片发生失速颤振。     

Zn-Al-Si钎料钎焊铜/铝接头显微组织及性能研究

采用Zn-14.1Al-0.9Si和Zn-21.5Al-1.5Si两种钎料钎焊获得铜/铝接头,研究了Cu/Zn-Al-Si/Al接头Cu母材/钎缝界面结构、钎缝中心区显微组织、接头抗剪切性能和断口形貌.研究发现,Cu/Zn-14.1Al-0.9Si/Al接头和Cu/Zn-21.5Al-1.5Si/Al接头界面结构均为Cu/扩散层/Al4.2Cu3.2Zn0.7,其中Al4.2Cu3.2Zn0.7化合物层厚度分别为1～2 μm和3～4μm.2种铜/铝接头钎缝中心区均由α-Al固溶体,η-Zn固溶体,Zn-Al共晶和Si单质组成,未发现脆性CuAl2化合物.由于具有较薄的界面化合物层,在剪切力作用下,Cu/Zn-14.1Al-0.9Si/Al接头断裂一部分起源于Al4.2Cu3.2Zn0.7化合物层,另部分起源于界面扩散层,而Cu/Zn-21.5Al-1.5Si/Al接头断裂均起源于较厚的Al4.2Cu3.2Zn0.7化合物层.因此,Cu/Zn-14.1Al-0.9Si/Al接头的抗剪切强度高于Cu/Zn-21.5Al-1.5Si/Al接头,分别为60.1MPa和55.6MPa.     

波音757客改货航电系统改装

简要介绍了波音757-200客改装货时航电系统改装的主要工作内容和改装工作中的关键点,以及为保证整体改装工作的进度而实施的的创新手段。     

Numerical investigation of flow mechanisms of tandem impeller inside a centrifugal compressor

This study numerically investigated a single stage centrifugal compressor ‘‘Radiver’’ with a wedge diffuser and several tandem-designed impellers to explore the flow phenomena within the tandem impeller and the potential to enhance compressor performance. The results demonstrate that tandem design and clocking fraction (λ_s) significantly affects the compressor performance. The compressor stage with tandem impellers of Series A of boundary layer growth interruption alone are observed to have a widely operating range but efficiency and total pressure ratio penalty compared with that of conventional impeller. The tandem impeller with at least the same impeller efficiency as the conventional design is considered as a critical design criteria so that further modification process based on the flow characteristic of tandem impeller is necessary. In order to restrain the inducer wake and exducer shock losses, parameters modification of blade angle and thickness distributions are necessary and the modified tandem impeller of Series B is obtained. The modified tandem impeller with 25% clocking arrangement shows an 8.45% stall margin increase and maintains the total pressure ratio and efficiency as the conventional design, which proves the potential of tandem impeller to improve compressor stage performance. It is noteworthy that the tandem impellers of Radiver have not shown obviously balanced exit flow field and the fundamental mechanism of stall margin extending of tandem impeller lies on the improved impeller/diffuser matching performance resulting from the incidence angle variation at diffuser inlet.     

边界层抽吸对超燃冲压发动机流场特性的影响研究

为了解边界层抽吸对超燃冲压发动机流场的影响,采用风洞试验和数值计算对隔离段激波串特性以及燃烧室燃烧特性进行了研究。结果表明,在发动机入口马赫数2.0,总温950K,总压0.82MPa的来流条件下,当量比为0.18先锋氢气与不同当量比煤油共同燃烧呈不稳定状态,激波串在隔离段内前后振荡传播。当煤油当量比为0.29时,激波串振荡前缘远离抽吸位置,边界层抽吸对发动机流场基本没有影响。随着煤油当量比逐渐增大,激波串前缘位置到达抽吸区附近,边界层抽吸开始产生影响,改变了隔离段内的激波串动态演化过程、形态结构以及位置分布,同时有效提高了隔离段抗反压特性,使得煤油最大当量比可以由0.38增大至0.42。此外,边界层抽吸对发动机内的亚燃/超燃区域分布也会产生影响。     

A CFD-based numerical virtual flight simulator and its application in control law design of a maneuverable missile model

A CFD-based Numerical Virtual Flight (NVF) simulator is presented, which integrates an unsteady flow solver on moving hybrid grids, a Rigid-Body Dynamics (RBD) solver and a module of the Flight Control System (FCS). A technique of dynamic hybrid grids is developed to control the active control surfaces with body morphing, with a technique of parallel unstructured dynamic overlapping grids generating proper moving grids over the deflecting control surfaces (e.g. the afterbody rudders of a missile). For the flow/kinematic coupled problems, the 6 Degree-Of-Freedom (DOF) equations are solved by an explicit or implicit method coupled with the URANS CFD solver. The module of the control law is explicitly coupled into the NVF simulator and then improved by the simulation of the pitching maneuver process of a maneuverable missile model. A nonlinear dynamic inversion method is then implemented to design the control law for the pitching process of the maneuverable missile model. Simulations and analysis of the pitching maneuver process are carried out by the NVF simulator to improve the flight control law. Higher control response performance is obtained by adjusting the gain factors and adding an integrator into the control loop.     

大涵道比风扇/增压级进气畸变数值模拟研究

为探究进口总压畸变下大涵道比风扇/增压级内部流场的主要特征，基于三维彻体力模型的思想，开发了一套能够实现风扇/增压级内外涵联算功能的三维数值计算程序。利用该程序模拟了某大涵道比风扇/增压级在周向总压畸变进气下的三维流场。计算结果表明：大涵道比风扇单转子不同叶高处的畸变传递特征差异较大，转子出口总压畸变强度由叶根到叶尖逐渐降低，在叶尖处衰减为最小值1.5%；在转子出口相应诱导出的总温畸变强度由叶根到叶尖逐渐升高，在叶尖处达到最大值1.4%；进口周向总压畸变导致风扇转子总压比下降0.5%，而风扇转子出口形成的总压总温复合畸变导致增压级总压比下降2%；总压畸变在增压级中呈逐级衰减趋势，而高温畸变区的周向范围在逐级增加。     

共轴刚性双旋翼/机身干扰流场数值模拟

采用滑移网格技术求解Navier-Stokes (RANS)方程的方法,研究了共轴刚性双旋翼/机身的干扰问题。通过Caradonna-Tung旋翼、Robin直升机、Maryland直升机旋翼/机身干扰和Harrington 2共轴双旋翼等算例,验证了所提出的旋翼流场数值模拟方法的正确性。在此基础上,以Maryland机身为原型,分析了不同桨距的共轴刚性双旋翼与机身之间的干扰特性。结果表明:所提出的数值模拟方法能够很好地模拟共轴刚性双旋翼/机身的气动干扰特性;由于机身对于共轴刚性双旋翼下洗流场的阻滞作用,旋翼的悬停效率增加5%左右,并且随着拉力系数的增大使得悬停效率的增量更加明显;旋翼的悬停效率增加主要来源于下旋翼0°方位角附近的桨叶升力系数的增大,并且拉力系数的增量由桨根向桨尖方向逐渐减小。      

CVD技术制备Ta/W层状复合材料

运用化学气相沉积(Chemical Vapor Deposition,CVD)技术制备了W体积分数分别10%,13%和18%的Ta/W两层层状复合材料,采用金相显微镜(OM)、扫描电镜(SEM)和室温拉伸实验对复合材料的性能进行分析。结果表明:运用CVD技术可以制备W体积分数不同,且密度优于理论密度99.4%的层状复合材料;复合材料中Ta,W层的晶粒均为柱状晶粒,离界面越近,晶粒越细;沉积态复合材料的力学性能优于纯CVD Ta和CVD W;1600℃×2 h的热处理后,复合材料的界面扩散层宽度显著增大,力学性能高于沉积态的力学性能,最高抗拉强度可达660 MPa。     

A coupling VWM/CFD/CSD method for rotor airload prediction

A coupling fluid-structure method with a combination of viscous wake model(VWM),computational fluid dynamics(CFD) and comprehensive structural dynamics(CSD) modules is developed in this paper for rotor unsteady airload prediction. The hybrid VWM/CFD solver is employed to model the nonlinear aerodynamic phenomena and complicated rotor wake dynamics;the moderate deflection beam theory is implemented to predict the blade structural deformation; the loose coupling strategy based on the ‘delt method' is used to couple the fluid and structure solvers.Several cases of Helishape 7A rotor are performed first to investigate the effect of elastic deformation on airloads. Then, two challenging forward flight conditions of UH-60 A helicopter rotor are investigated, and the simulated results of wake geometry, chordwise pressure distribution and sectional normal force show excellent agreement with available test data; a comparison with traditional CFD/CSD method is also presented to illustrate the efficiency of the developed method.